膨胀效应对激波/湍流边界层干扰的影响

采用直接数值模拟方法对来流马赫数2.9,30°激波角的入射激波与膨胀角湍流边界层干扰问题进行了数值研究。入射激波在壁面上的名义入射点固定在膨胀角角点,膨胀角角度分别取为0°、2°、5°和10°。通过改变膨胀角角度,考察了膨胀效应对干扰区内复杂流动现象的影响规律和作用机制,如分离泡、物面压力脉动特性、膨胀区湍流边界层和物面剪切应力脉动场等。研究发现,膨胀角角度的增大使得分离区流向长度和法向高度急剧降低,尤其是在强膨胀效应下分离泡形态呈现整体往下游偏移的双峰结构。物面压力脉动功率谱结果表明,膨胀角为2°和5°时,分离激波的非定常运动仍表征为大尺度低频振荡,而膨胀角为10°,强膨胀效应极大地抑制了分离激波的低频振荡,加速了下游再附边界层物面压力脉动的恢复过程。膨胀区湍流边界层雷诺剪切应力各象限事件贡献和出现概率呈现逐步恢复到上游湍流边界层的趋势,Görtler-like流向涡结构展向和法向尺度变化剧烈,同时在近壁区将诱导生成大量小尺度流向涡。此外,物面剪切应力脉动场的本征正交分解分析指出,膨胀效应的影响体现在低阶模态能量的急剧降低从而使得高阶模态的总体贡献相对升高。     

基于DS算法的混胺燃料近红外光谱分析模型传递

对混胺燃料的近红外光谱分析模型的传递方法进行研究。采用 K/S(Kennard/Stone)算法选择转换集样品,采摘用直接校正(Direct Standardization,DS)算法对从仪器采集的光谱进行校正。通过光谱平均差异(ARMS)比较奇异值分解(Singular Value Decomposition,SVD)算法和偏最小二乘法(Partial Least Squares,PLS)对光谱校正的效果。当 PLS算法的最佳主因子数为 3时,DS-PLS算法的光谱校正率可达到 97.5%,优于 DS-SVD算法。混胺样品的分析模型经过 DS-PLS算法传递后,对从仪器的混胺样品各项指标的预测标准偏差(SEP)明显好于传递前,与主仪器预测效果接近,说明采用 K/S算法选择合适的转换集样品后,通过 DS-PLS模型传递算法可有效降低仪器间的光谱差异,实现近红外光谱分析模型在各台光谱仪之间共享。     

In-orbit assessment of laser retro-reflector efficiency onboard high orbiting satellites

The navigation and geodetic satellites that orbit the Earth at altitudes of approximately 20,000 km are tracked routinely by many of the Satellite Laser Ranging (SLR) stations of the International Laser Ranging Service (ILRS). In order to meet increasing demands on SLR stations for daytime and nighttime observations, any new mission needs to ensure a strong return signal so that the target is easily acquirable. The ILRS has therefore set a minimum effective cross-section of 100 million square metres for the on-board laser retro-reflector arrays (LRAs) and further recommends the use of ‘uncoated’ cubes in the arrays. Given the large number of GNSS satellites that are currently supported by SLR, it is informative to make an assessment of the relative efficiencies of the various LRAs employed. This paper uses the laser ranging observations themselves to deduce and then compare the efficiencies of the LRAs on the COMPASS-M1 navigation satellite, two satellites from the GPS and three from the GLONASS constellations, the two GIOVE test satellites from the upcoming Galileo constellation, the two Etalon geodetic spheres and the geosynchronous communications test satellite, ETS-8. All the LRAs on this set of satellites employ back-coated retro-reflector cubes, except those on the COMPASS-M1 and ETS-8 vehicles which are uncoated. A measure of return signal strength, and thus of LRA-efficiency, is calculated using the laser-range full-rate data archive from 2007 to 2010, scaled to remove the effects of variations in satellite range, atmospheric attenuation and retro-reflector target total surface area. Observations from five SLR stations are used in this study; they are Herstmonceux (UK), Yarragadee (Australia), Monument Peak and McDonald (USA) and Wettzell (Germany). Careful consideration is given to the treatment of the observations from each station in order to take account of local working practices and system upgrades. The results show that the uncoated retro-reflector cubes offer significant improvements in efficiency.     

选区熔化过程多尺度多物理场建模研究进展

选区熔化技术是一种基于粉末床的、能够精确成形复杂零件、调控微观组织和性能的金属增材制造技术,其成形过程的计算机模拟对于生产实践具有重要指导意义。综述了国内外的研究现状,首先介绍选区熔化技术的原理及其特点;然后介绍国内外对选区熔化过程已经开展的计算机模拟技术的研究进展;并进一步重点介绍针对电子束选区熔化过程的多尺度多物理场模型,主要包括:(1)微观尺度电子束与材料相互作用的能量吸收模型;(2)细观尺度从铺粉到粉末加热、熔化、流动、沉积成形全过程的模型;(3)宏观尺度零件成形过程模型。     

Determination of station positions and velocities from laser ranging observations to Ajisai,Starlette and Stella satellites

The positions and velocities of the four Satellite Laser Ranging (SLR) stations: Yarragadee (7090), Greenbelt (7105), Graz (7839) and Herstmonceux (7840) from 5-year (2001–2005) SLR data of low orbiting satellites (LEO): Ajisai, Starlette and Stella were determined. The orbits of these satellites were computed from the data provided by 20 SLR stations. All orbital computations were performed by means of NASA Goddard’s GEODYN-II program. The geocentric coordinates were transformed to the topocentric North–South, East–West and Vertical components in reference to ITRF2005. The influence of the number of normal points per orbital arc and the empirical acceleration coefficients on the quality of station coordinates was studied. To get standard deviation of the coordinates determination lower than 1 cm, the number of the normal points per site had to be greater than 50. The computed positions and velocities were compared to those derived from LAGEOS-1/LAGEOS-2 data. Three parameters were used for this comparison: station coordinates stability, differences from ITRF2005 positions and velocities. The stability of coordinates of LEO satellites is significantly worse (17.8 mm) than those of LAGEOS (7.6 mm), the better results are for Ajisai (15.4 mm) than for Starlette/Stella (20.4 mm). The difference in positions between the computed values and ITRF2005 were little bit worse for Starlette/Stella (6.6 mm) than for LAGEOS (4.6 mm), the results for Ajisai were five times worse (29.7 mm) probably due to center of mass correction of this satellite. The station velocities with some exceptions were on the same level (≈1 mm/year) for all satellites. The results presented in this work show that results from Starlette/Stella are better than those from Ajisai for station coordinates determination. We can applied the data from LEO satellites, especially Starlette and Stella for determination of the SLR station coordinates but with two times lower accuracy than when using LAGEOS data.     

辽宁对日本贸易及吸收日资效应的实证分析

日本是辽宁重要的经贸国家之一,在辽宁对外经贸中起着极为重要的作用。研究对日经贸关系及其对辽宁经济的影响,有利于辽宁区域经济的发展。从辽宁与日本的经贸关系出发,运用相关的统计数据,建立回归模型来实证分析辽宁与日贸易及吸收日资对辽宁经济所产生的推动效应,最后阐述了辽宁与日本经贸关系的前景,从而对辽宁与日本的经贸关系有更深刻地认识。     

线性调频半导体激光衍射光栅干涉仪

介绍一种以线性调频半导体激光为光源的衍射光栅干涉仪。激光与光栅上衍射的±１级衍射波会合，由于有光程差而发生光拍频，测量拍频信号的相位移则可测得光栅的位移。设计了一种克服激光波长漂移和空气折射率变化影响的对称差动光路，使这种方法达到实用化的程度，分辨力达到纳米级。此外，还介绍了应用于接触干涉仪的实验情况。     

脉冲激光测距误差标定及不确定度分析CSCD

以脉冲激光测距机的测距误差标定为背景,通过对测距误差解析表达式的推导,给出了系统各不确定度分量对测距误差的影响,计算了信号延迟时间、探测器和激光二极管响应时间、晶振频率、大气折射率等不确定度分量。通过对某已标定激光测距机实验验证表明:该装置在500m^20 000m测距范围内,测量重复性引入的相对标准不确定度最大值为0.67m,满足该类激光测距机测量不确定度5m(k=2)的校准测试需求。因此,利用该解析表达式可以实现对脉冲激光测距误差的有效评估,这对于脉冲激光测距测试系统、脉冲激光测距机的设计具有重要的指导意义。     

基于零空间的改进直接分配法

直接分配法是解决操纵面冗余飞行器控制分配的一种有效方法,但直接分配法只能对指定方向上误差最小目标进行优化,这种缺点限制了直接分配法的应用。零空间可以在保持转矩不变的前提下对控制量进行调节,利用这种特性,在三维转矩直接分配的基础上,通过对零空间坐标K进行数学规划可以使其他性能指标达到最优。推导证明,控制量最小问题和阻力最小问题分别可以转化为对坐标K的线性规划与二次规划问题。仿真结果表明,给出的基于零空间的改进直接分配法可以实现控制量最小和阻力最小控制分配。     

一种用于液晶曝光中的激光检测系统

介绍了一种非接触式激光检测系统，可用于检测液晶曝光中液晶模板与基板之间的间隙，给出了该种系统的测量原理、硬件系统、信号处理方法、测量结果、分辨力和误差分析，并指出了这种测量系统的应用。